Home

System Would Acquire Core and Powder Samples of Rocks

A sampling system would be built around an ultrasonic/sonic drill corer.

A system for automated sampling of rocks, ice, and similar hard materials at and immediately below the surface of the ground is undergoing development. The system, denoted a sample preparation, acquisition, handling, and delivery (SPAHD) device, would be mounted on a robotic exploratory vehicle that would traverse the terrain of interest on the Earth or on a remote planet. The SPAHD device would probe the ground to obtain data for optimization of sampling, prepare the surface, acquire samples in the form(s) of cores and/or powdered cuttings, and deliver the samples to a selected location for analysis and/or storage.

ImageThe SPAHD device would be built around an ultrasonic/sonic drill corer (USDC) — an apparatus that was reported in “Ultrasonic/Sonic Drill/ Corers With Integrated Sensors” (NPO-20856), NASA Tech Briefs, Vol. 25, No. 1 (January 2001), page 38. To recapitulate: A USDC includes a hollow drill bit or corer, in which combinations of ultrasonic and sonic vibrations are excited by an electronically driven piezoelectric actuator. The corer can be instrumented with a variety of sensors (and/or the drill bit or corer can be used as an acoustic impedance sensor) for both probing the drilled material and acquiring feedback for control of the excitation. The USDC advances into the material of interest by means of a hammering action and a resulting chiseling action at the tip of the corer. The hammering and chiseling actions are so effective that unlike in conventional twist drilling, a negligible amount of axial force is needed to make the USDC advance into the material. Also unlike a conventional twist drill, the USDC operates without need for torsional restraint, lubricant, or a sharp bit.

ImageIn addition to a USDC, the SPAHD device (see Figure 1) would include sensor, control, and communication subsystems; a subsystem for positioning the USDC at the desired position and orientation on the ground; a set of interchangeable USDC bits; a tool rack to store the bits; and mechanisms for manipulating and delivering samples. The bits would be attached to, and detached from, a resonator horn of the piezoelectric actuator by means of simple-to-operate snap-on/snap-off mechanisms. The set of bits would includlly driven piezoelectric actuator. The corer can be instrumented with a variety of sensors (and/or the drill bit or corer can be used as an acoustic impedance sensor) for both probing the drilled material and acquiring feedback for control of the excitation. The USDC advances into the material of interest by means of a hammering action and a resulting chiseling action at the tip of the corer. The hammering and chiseling actions are so effective that unlike in conventional twist drilling, a negligible amount of axial force is needed to make the USDC advance into the material. Also unlike a conventional twist drill, the USDC operates without need for torsional restraint, lubricant, or a sharp bit.

In addition to a USDC, the SPAHD device (see Figure 1) would include sensor, control, and communication subsystems; a subsystem for positioning the USDC at the desired position and orientation on the ground; a set of interchangeable USDC bits; a tool rack to store the bits; and mechanisms for manipulating and delivering samples. The bits would be attached to, and detached from, a resonator horn of the piezoelectric actuator by means of simple-to-operate snap-on/snap-off mechanisms. The set of bits would include a probing bit, bits for cutting cores and collecting powdered cuttings, bits for extracting the cores after they have been cut (see Figure 2), and an ultrasonic rock abrasion tool (URAT) bit [described in “Ultrasonically Actuated Tools for Abrading Rock Surfaces” (NPO-30403), NASA Tech Briefs, Vol. 30, No. 7 (July, 2006), page 58.

This work was done by Yoseph Bar-Cohen, James Randolph, Xiaoqi Bao, Stewart Sherrit, Chuck Ritz, and Greg Cook of Caltech for NASA’s Jet Propulsion Laboratory. For further information, access the Technical Support Package (TSP) free online at www.techbriefs.com/tsp under the Machinery/Automation category. NPO-30640

This Brief includes a Technical Support Package (TSP).

System Would Acquire Core and Powder Samples of Rocks (reference NPO-30640) is currently available for download from the TSP library.

Please Login at the top of the page to download.