Mechanical Components

Hybrid Aerial/Rover Vehicle

This robotic vehicle would combine features of balloons and "beach-ball" rovers. A proposed instrumented robotic vehicle called an "aerover" would fly, roll along the ground, and/or float on bodies of liquid, as needed. The aerover would combine features of an aerobot (a robotic lighter-than-air balloon) and a wheeled robot of the "rover" class. An aerover would also look very much like a variant of the "beach-ball" rovers described in "Lightweight 'Beach- Ball' Robotic Vehicles" (NPO-20283), NASA Tech Briefs, Vol. 22, No. 7 (July 1998), page 74. Although the aerover was conceived for use in scientific exploration of Titan (the largest moon of the planet Saturn), the aerover concept could readily be adapted to similar uses on Earth.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

Compliant Gripper for a Robotic Manipulator

Diverse small objects can be manipulated without force-feedback control. The figure depicts a prototype of a robotic-manipulator gripping device that includes two passive compliant fingers, suitable for picking up and manipulating objects that have irregular shapes and/or that are, themselves, compliant. The main advantage offered by this device over other robotic-manipulator gripping devices is simplicity: Because of the compliance of the fingers, force-feedback control of the fingers is not necessary for gripping objects of a variety of sizes, shapes, textures, and degrees of compliance. Examples of objects that can be manipulated include small stones, articles of clothing, and parts of plants.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

Accurate Spring Testing

Load-testing machine features can affect the accuracy, precision, repeatability, and reproducibility of test results. Virtually all spring manufacturers must test their products with some kind of load testing machine. Testing ensures that the product is produced and shipped within the customer's specifications. Or does it? Disputes over test results still occur that can cause a multitude of costly problems: returned product, delayed payment, product liability, or customer dissatisfaction. The quality of a spring testing program can largely affect these problems and their associated cost.

Posted in: Mechanical Components, Briefs

Read More >>

Pneumatically Actuated Miniature Peristaltic Vacuum Pumps

Small, rugged, low-power pumps could be fabricated inexpensively. Pneumatically actuated miniature peristaltic vacuum pumps have been proposed for incorporation into advanced miniature versions of scientific instruments that depend on vacuum for proper operation. These pumps are expected to be capable of reaching vacuum-side pressures in the torr to millitorr range (from ≈133 down to ≈0.13 Pa). Vacuum pumps that operate in this range are often denoted roughing pumps. In comparison with previously available roughing pumps, these pumps are expected to be an order of magnitude less massive and less power-hungry. In addition, they would be extremely robust, and would operate with little or no maintenance and without need for oil or other lubricants. Portable mass spectrometers are typical examples of instruments that could incorporate the proposed pumps. In addition, the proposed pumps could be used as roughing pumps in general laboratory applications in which low pumping rates could be tolerated.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

Miniature Gas-Turbine Power Generator

Energy density would greatly exceed that of a typical battery system. A proposed microelectromechanical system (MEMS) containing a closed- Brayton-cycle turbine would serve as a prototype of electric- power generators for special applications in which high energy densities are required and in which, heretofore, batteries have been used. The system would have a volume of about 6 cm3 and would operate with a thermal efficiency >30 percent, generating up to 50 W of electrical power. The energy density of the proposed system would be about 10 times that of the best battery-based systems now available, and, as such, would be comparable to that of a fuel cell.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

Improved Gear Shapes for Face Worm Gear Drives

These shapes offer potential for increasing precision and reducing vibration and noise. Shapes different from the traditional ones have been proposed for face worm gears and for conical and cylindrical worms that mesh with them. The proposed shapes are based on the concept of generating a face worm gear surface by use of a tilted head cutter instead of by the traditional use of a hob. (As used here, “head cutter” is also meant to signify, alternatively, a head grinding tool.)The gear-surface-generation equipment would be similar to that used for generation of spiral bevel and hypoid gears. In comparison with the corresponding traditional hob, a tilted head cutter according to the proposal would be larger, could be fabricated with greater precision, and would enable the generation of gear surfaces with greater precision and greater productivity.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

Alternative Way of Shifting Mass To Move a Spherical Robot

A payload would change its position by lengthening and shortening suspension cables. An alternative method of controlled shifting of the center of mass has been proposed as a means of locomotion of a robot that comprises mostly a payload inside a hollow, approximately spherical shell. The method would be applicable to robots that include rigid, semirigid, or flexible inflated shells, including those of the “beach-ball rover” type, variants of which have been described in several previous NASA Tech Briefs articles.

Posted in: Mechanical Components, Briefs, TSP

Read More >>

White Papers

Oscilloscope Fundamentals Primer
Sponsored by Rohde and Schwarz
Windows CE Development for RISC Computers Made Easy
Sponsored by Sealevel
Troubleshooting EMI in Embedded Designs
Sponsored by Rohde and Schwarz A and D
Design Considerations to Meet the Urgent Demand for Miniaturization of Electronics in Military Applications
Sponsored by Fischer Connectors
Specialized Adhesives Withstand Thermal Cycling
Sponsored by Master Bond
Solar Electric Systems – Power Reliability
Sponsored by SunWize

White Papers Sponsored By: