Thermal Issues

Figure 4. The Class AAA Sol3A Solar Simulator by Newport s Oriel division.
A significant source of uncertainty in PV testing is the lack of knowledge of the temperature, Tcell, at the space charge region of the cell. The package that houses a cell in a solar reference cell, for example, acts as a heat sink that cools the back of the cell (by conduction) faster than the top surface of the cell (by convection).This makes the bottom surface, generally speaking, a few degrees C cooler than the top surface of the cell. The built-in thermocouple in a solar reference cell measures the temperature at the back of the cell which is different from Tcell. A lack of knowledge of the temperature difference translates into uncertainty in the performance parameter, which is proportional to the temperature coefficient.

The difference in temperatures is apparent when the parameter (e.g. open-circuit voltage) is plotted against temperature (at the back of the cell) when the cell is heated or cooled (Figure 2). As the best estimate of the open circuit voltage, the two lines in Figure 2 can be extrapolated to 25°C using the temperature coefficient, and the midpoint of the two Voc intercepts at 25°C can be calculated. For more accurate measurement, we let the cell equilibrate at room temperature and measure the parameters using only momentary illumination (~ 1 sec). The measurement then is extrapolated to 25°C using their respective temperature coefficients.

Additional uncertainty (i.e. “error” ) arises from a mismatch of light source spectra and spectral response of the cell. This error source is known as the spectral mismatch error and is expressed in terms of the absolute deviation of the spectral mismatch factor M from unity. The mismatch refers to the relative differences in spectral distributions of the light used to measure the reference and the device under test, respectively, and the relative differences in the spectral responses of the two devices. Matching the spectra and responses as closely as possible minimizes this error. A value of M = 1 indicates a perfect match. Deviations from unity can be as much as 50%1.

The Newport TAC — PV Lab uses a solar reference cell with a KG1 filter window (instead of the standard fused silica) to test organic devices. Doing so keeps the mismatch below 10%. Of course, there is error in the correction factor M itself due to inaccurate knowledge of the spectral distribution of sunlight and spectral response of either device. To meet this challenge, Newport’s Oriel division has developed an instrument, the IQE-200, which can accurately measure the spectral response of most PV devices.

Another error encountered in PV measurements employing simulated sunlight is due to the spatial non-uniformity in the solar simulator beam (Figure 3).

Solar simulator light is typically more concentrated in the center (around the optical axis) than at the edge of the illuminated area and maps into a domed surface, the height of which can be used as a metric for spatial non-uniformity. Spatial non-uniformity is minimized (under 2%) in Class AAA solar simulators like the Sol3A from Newport Oriel (Figure 4). The residual amount of spatial non-uniformity causes irradiance error that is proportional to the relative areas of the solar reference cell and device under test, and on the relative locations of the two cells within the working plane of the solar simulator. Alternatively, a factor (analogous to the spectral mismatch factor) can be calculated and applied to correct for this error2.

Unlike packaged solar reference cells, experimental or prototype cells sometimes arrive at the Newport TAC-PV Lab unpackaged. In many cases, they degrade with exposure to air, light, heat and humidity. These are delicate structures as small as 0.04 cm2 that may simply be sandwiched between two microscope slides. Light exposure during testing must be short to be non-invasive, but no shorter than the response time of the cell. There is often no convenient way to control or directly measure the temperature of these devices. The TAC-PV Lab tests experimental cells under short exposure to light (~ 1 sec) as produced by the Newport Oriel Sol3A solar simulator with a built-in shutter with 300 ms switching time. This technique perturbs the cell only slightly from being in equilibrium with room temperature. Variations in Voc during the exposure to light can be used as a measure of deviation from equilibrium3. Repeating these short exposures at different bias voltages generates an I-V curve from which all the electrical performance parameters can be calculated.

This article was written by Ruben Zadoyan, PhD, Senior Director, and Matthew O Donnell, PV Lab Manager, Technology & Applications Center, Newport Corporation (Irvine, CA). For more information, contact Mr. Zadoyan at This email address is being protected from spambots. You need JavaScript enabled to view it., or visit http://info.hotims.com/28057-200.


  1. C. R. Osterwald, “Translation of device performance measurements to reference conditions.” Solar Cells, 18, pp. 269-279 (1988).
  2. Klaus Heidler, Heike Fischer, and Siegfried Kunzelmann, “New approaches to reduce uncertainty in solar cell efficiency measurements introduced by nonuniformity or irradiance and porr FFdetermination.” Proceedings of the 9th EC Photovoltaic solar energy conference, Freiburg, Germany, pp. 791-4 (1989).
  3. K. Emery and T. Moriarty, “Accurate measurement of organic solar cell efficiency,” Proc. SPIE Optics + Photonics, session 7052-12, San Diego, CA, Aug. 10-14, (2008).
« Start Prev 1 2 Next End»

The U.S. Government does not endorse any commercial product, process, or activity identified on this web site.