Electronic Components

Researchers Print the Unprintable: Kapton

Kapton, a material used in electronics and aerospace applications, has only been available in sheet form. Researchers from Virginia Tech have found a way to 3D-print a polymer with Kapton's structural characteristics.

Posted in: News, News, Aerospace, Electronic Components, Electronics, Electronics & Computers, Coatings & Adhesives, Materials

Writing with Light: An ‘Etch A Sketch’ Electrical Circuit

Physicists from Washington State University (WSU) have used lasers to draw conductive circuits into a crystal. The achievement demonstrates a new kind of transparent, three-dimensional electronics: circuits that can be erased and reconfigured, like the drawings of an Etch A Sketch.

Posted in: News, Board-Level Electronics, Electronic Components, Electronics & Computers, Lasers & Laser Systems, Optical Components, Optics, Photonics

Novel Computer Chips Could Bridge Gap Between Computation and Storage

Computer chips in development at the University of Wisconsin–Madison could make future computers more efficient and powerful by combining tasks usually kept separate by design. Jing Li, an assistant professor of electrical and computer engineering at UW–Madison, is creating computer chips that can be configured to perform complex calculations and store massive amounts of information within the same integrated unit — and communicate efficiently with other chips. She calls them “liquid silicon.”

Posted in: News, Computers, Electronic Components, Electronics, Semiconductors & ICs

Carbon Nanofibers Synthesized on Selective Substrates for Nonvolatile Memory and 3D Electronics Applications

NASA’s Jet Propulsion Laboratory has developed a nano-electro-mechanical resonator (NEMR) based on vertically aligned carbon nanofibers (CNFs) that is suitable for applications requiring high sensitivity, broad tenability, low loss (high Q), low power consumption, and small size. Other nanoscale resonators have been demonstrated using top-down fabrication approaches, but these generally involve complicated and expensive electron beam lithography. JPL’s bottom-up fabrication approach yields robust, vertically oriented CNFs that can be used to form high-Q, high-frequency NEMRs. In addition, the resonant frequency of these NEMRs can be tuned by selecting the length and diameter of the CNFs. This allows for a highly integrated, ultra-low-power, high-data-rate, and wide-bandwidth NEMR-based transceiver architecture.

Posted in: Briefs, Electronic Components, Electronics & Computers, Architecture, Electronic equipment, Architecture, Electronic equipment, Nanomaterials

A Nanotube Film Electrode and Electroactive Device Fabricated with the Nanotube Film Electrode and Methods for Making the Same

Applications include optical devices, electromechanical energy conversion, medical devices, sonar, and transducers.

NASA’s Langley Research Center offers an all-organic electroactive device system fabricated with single-wall carbon nanotubes (SWCNT). The enhanced design offers higher electroactive performance in comparison with conventional electroactive device systems fabricated with metal electrodes or other conducting polymers. The new structure allows for significant improvement of the electroactive strain due to relief of the constraint on the electroactive layer. It exhibits superb actuation properties and can withstand high temperatures with improved mechanical integrity and chemical stability. In addition, the electroactive device can be made transparent, allowing for use in optical devices. NASA is seeking development partners and potential licensees.

Posted in: Briefs, Electronic Components, Electronics & Computers, Electronic equipment, Optics, Electronic equipment, Optics, Nanomaterials

Superconducting Transition Edge Sensors and Methods for Design and Manufacture Thereof

Superconducting Transition Edge Sensors and Methods for Design and Manufacture Thereof

NASA technologists have developed a novel, superconducting transition edge sensor (TES). Such TES devices are thermometers that are widely used for particle detection, e.g. X-rays, infrared photons, atoms, molecules, etc. Energy resolution is chiefly important in superconducting transition edge sensors to function as imaging spectrometers. For optimal energy resolution, it is necessary to control the superconducting transition temperature for the device.

Posted in: Briefs, Electronic Components, Electronics & Computers, Design processes, Imaging, Imaging and visualization, Sensors and actuators, Imaging, Imaging and visualization, Sensors and actuators, Fabrication

Chalcogenide Nanoionic-Based Radio Frequency Switch

The electrochemical switch is non-volatile, lacks moving parts that can fail, and is easy to fabricate.

NASA’s Glenn Research Center has developed nanoionic-based radio frequency (RF) switches for use in devices that rely on low-power RF transmissions, such as automotive systems, RFID technology, and smartphones. These groundbreaking nanoionic switches operate at speeds of semiconductor switches, and are more reliable than microelectromechanical systems (MEMS) switches while retaining the superior RF performance and low power consumption found in MEMS, all without the need for higher electrical voltages. In this new process, metals are photo-dissolved into a chalcogenide glass and packaged with electrodes and a substrate to form a switch. Since the nanoionic-based switch is electrochemical in nature, it has certain advantages over switches that are mechanically based, including nonvolatility, lack of moving parts that can fail, ease and efficiency of activation, and ease of fabrication. This innovative device has the potential to replace MEMS and semiconductors in a wide range of switching systems, including rectifying antennas (rectennas) and other RF antenna arrays.

Posted in: Briefs, Electronic Components, Electronics & Computers, RF & Microwave Electronics, Radio equipment, Switches, Radio equipment, Switches, Radio-frequency identification, Nanotechnology

X-ray Diffraction (XRD) Characterization Methods for Sigma=3 Twin Defects in Cubic Semiconductor (100) Wafers

This technology is especially relevant in high-end, high-speed electronics.

NASA’s Langley Research Center has developed a method of using x-ray diffraction (XRD) to detect defects in cubic semiconductor (100) wafers. The technology allows non-destructive evaluation of wafer quality in a simple, fast, inexpensive process that can be easily incorporated into an existing fab line. The invention adds value throughout the semiconductor industry, but is especially relevant in high-end, high-speed electronics where wafer quality has a more significant effect on yields.

Posted in: Briefs, Electronic Components, Electronics & Computers, Semiconductors, X-ray inspections

System for Configuring Modular Telemetry Transponders

Possible applications include weather monitoring and forecasting, Earth observation, and ionospheric studies.

Researchers at NASA’s Marshall Space Flight Center have developed software-defined radio (SDR) telemetry transceiver technology to collect and transmit data to and from small satellites and microsatellites. The SDR concept uses a minimal number of traditional analog radio-frequency components to convert RF signals to a digital format. Digital signal processing replaces bulky radio-frequency components, and enables reduced cost as well as size, weight, and power requirements (SWaP). The NASA technology enables software and firmware updates that increase the lifespan and efficacy of satellites, supporting a wide variety of changing radio protocols as they are developed. A modular design enables inclusion of multiple band frequency transmitters and receivers (S-band, X-band, Ka-band, etc.). The NASA SDR can find use in satellite applications in which cost savings, upgradability, and reliability are essential. A first-generation SDR has been flight tested on NASA’s FASTSAT mission.

Posted in: Briefs, Electronic Components, Electronics & Computers, Computer software / hardware, Computer software and hardware, Satellite communications, Computer software / hardware, Computer software and hardware, Satellite communications, Satellites

Sandia, Harvard Team Create First Quantum Computer Bridge

By forcefully embedding two silicon atoms in a diamond matrix, Sandia researchers have demonstrated for the first time on a single chip all the components needed to create a quantum bridge to link quantum computers together.

Posted in: News, Computers, Electronic Components, Electronics, Electronics & Computers

The U.S. Government does not endorse any commercial product, process, or activity identified on this web site.