Grid-Scale Energy Image
Leo Small (back right) and Erik Spoerke (back left) observe as Martha Gross (front) works in an argon glovebox on their lab-scale sodium iodide battery. This new kind of molten sodium battery could prove to be a lower-temperature, lower-cost battery for grid-scale energy storage.

Molten sodium batteries have been used for many years to store energy from renewable sources, such as solar panels and wind turbines. However, commercially available molten sodium-sulfur batteries typically operate at 520 – 660 °F (270 – 350 °C). Sandia’s new molten sodium battery operates at a much cooler 230 °F (110 °C) instead.

“There’s a whole cascading cost savings that comes along with lowering the battery temperature. You can use less expensive materials. The batteries need less insulation and the wiring that connects all the batteries can be a lot thinner,” said lead researcher Leo Small.

However, the battery chemistry that works at 550 °F doesn’t work at 230 °F, he added. Among the major innovations that allowed this lower operating temperature was the development of what he calls a catholyte. A catholyte is a liquid mixture of two salts, in this case, sodium iodide and gallium chloride.

A basic lead-acid battery, commonly used as a car ignition battery, has a lead plate and a lead dioxide plate with a sulfuric acid electrolyte in the middle. As energy is discharged from the battery, the lead plate reacts with sulfuric acid to form lead sulfate and electrons. These electrons start the car and return to the other side of the battery, where the lead dioxide plate uses the electrons and sulfuric acid to form lead sulfate and water. For the new molten sodium battery, the lead plate is replaced by liquid sodium metal, and the lead dioxide plate is replaced by a liquid mixture of sodium iodide and a small amount of gallium chloride.

When energy is discharged from the new battery, the sodium metal produces sodium ions and electrons. On the other side, the electrons turn iodine into iodide ions. The sodium ions move across a special ceramic separator to the other side where they react with the iodide ions, to form molten sodium iodide salt. Instead of a sulfuric acid electrolyte, the middle of the battery is a special ceramic separator that allows only sodium ions to move from side to side, nothing else.

In their new system, unlike a lithium-ion battery, everything is liquid on the two sides. That means you don’t have to deal with issues like the material undergoing complex phase changes or falling apart. These liquid-based batteries don’t have as limited a lifetime as many other batteries. In fact, commercial molten sodium batteries have lifetimes of 10 – 15 years, longer than standard lead-acid batteries or lithium-ion batteries.

Sandia’s small, lab-scale sodium iodide battery was tested for eight months inside an oven. The battery was charged and discharged more than 400 times over those eight months. Because of the COVID-19 pandemic, they had to pause the experiment for a month and let the molten sodium and the catholyte cool down to room temperature and freeze, but after warming the battery up, it still worked. This means that if a large-scale energy disruption were to occur, like what occurred in Texas in February, the sodium iodide batteries could be used, and then allowed to cool until frozen. Once the disruption was over, they could be warmed up, recharged, and returned to normal operation without a lengthy or costly start-up process, and without degradation of the battery’s internal chemistry.

Sodium iodide batteries are also safer. “A lithium-ion battery can catch on fire when there is a failure inside the battery, leading to runaway overheating. We’ve proven that cannot happen with our battery chemistry. Our battery, if you were to take the ceramic separator out, and allow the sodium metal to mix with the salts, nothing happens. Certainly, the battery stops working, but there’s no violent chemical reaction or fire,” said Erik Spoerke, a materials scientist who has been working on molten sodium batteries for more than a decade.

If an outside fire engulfs a sodium iodide battery, it is likely the battery will crack and fail, but it shouldn’t add fuel to the fire or cause a sodium fire. Additionally, at 3.6 volts, the new sodium iodide battery has a 40% higher operating voltage than a commercial molten sodium battery. This higher voltage leads to higher energy density, and that means that future batteries made with this chemistry would need fewer cells, fewer connections between cells, and an overall lower unit cost to store the same amount of electricity.

The next step for the sodium iodide battery project is to continue to tune and refine the catholyte chemistry to replace the gallium chloride component, Small said. Gallium chloride is very expensive, more than 100 times as expensive as table salt.

The team is also working on various engineering tweaks to get the battery to charge and discharge faster and more fully. One previously identified modification to speed up the battery charging was to coat the molten sodium side of the ceramic separator with a thin layer of tin.

Spoerke added that it would likely take five to 10 years to get sodium iodide batteries to market, with most of the remaining challenges being commercialization challenges, rather than technical challenges.