Electrical/​Electronics

Microwave power transmission using rectenna technology has attracted a strong interest in conjunction with wireless electric power delivery to infrastructure and subjects located at a remote place. A typical rectenna, which is a major...

Every LiDAR design faces the classic balancing act of signal versus noise. In order to maximize the range of a LiDAR, a receiver must amplify fractions of a micro-amp of photo current into a usable range for signal processing to occur, but...

The Flash LIDAR Emulator is a computer system designed to be functionally equivalent to a Flash LIDAR sensor camera. The system has the same hardware interfaces as the sensor, and produces images of comparable quality to the flash LIDAR sensor in real time (30 frames per second). The emulator is then used as a substitute for...

Carbon nanotubes (CNTs) are being studied for use in high-strength/lowweight composites and other applications. Recent research on thermal dissipation materials for high-power electronic devices is generating a lot of interest in various industries. Carbon nano tubes have attracted much attention due to their...

NASA’s Deep Space Network (DSN) is looking to modernize aging downlink receivers for telemetry, tracking, and radio science. It is looking to replace multiple types of custom-built, special-purpose receivers with a unified receiver architecture that...

Ceramic Column Grid Array (CCGA) packages have been increasing in use based on advantages such as high interconnect density, very good thermal and electrical performance, compatibility with standard surface-mount packaging assembly processes,...

Aradiation-hard, 130-Volt, 100-KHz capable, quad-channel operational amplifier with corresponding power supply and 6th-order Bessel filter circuitry has been designed, fabricated, and successfully tested. To control two-axis microelectromechanical systems (MEMS)-based mirrors, a differential...

Microwave interferometry provides a means of synthesizing large scanning antennas that are not otherwise physically practical for spaceborne Earth observational systems. By cross-correlating multiple receivers of an array, high-resolution images are synthesized from a sparse — or thinned — array of...

In this work, there were four independent vision modules implemented in an FPGA: a CameraLink camera interface, rectification, bilateral filtering, and stereo disparity correlation. Each module was originally designed to run from end to end, not in a pipeline with the other modules. This limited...

Power consumption during all phases of spacecraft flight is of great interest to the aerospace community. As a result, significant analysis effort is exerted by both system and electrical-domain engineers to understand the rates of electrical energy generation and consumption under many...

When solar cells are electrically connected to form solar arrays, they are organized into strings. Each string represents a specific number of cells connected in series to produce a specific voltage. The strings are then connected in parallel to add their currents to meet the array power requirement....

High-energy-density and safe rechargeable batteries are required for NASA’s future exploration missions. Lithium-ion (Li-ion) batteries are attractive energy storage systems due to their relatively high energy and power densities. However, the unfavorable side reactions between...

Radio frequency (RF) microelectromechanical system (MEMS) switches have advantages over their solid-state counterparts. However, ohmic contact MEMS devices face several significant limitations, preventing entry into the mass market. These limitations are cost, reliability, packaging, and integration.

The University of California Los Angeles (UCLA) has developed a wide range of CMOS (complementary metal–oxide–semiconductor) phase lock loop (PLL) chips with self-healing/self-calibration capabilities, allowing them to adapt, on the fly, to changes in temperature and other environment...

The temperature of the orbiting space station’s Sun-facing side could be up to 250 °F (≈120 °C) and will be a significant antenna noise temperature contributor for visiting spacecraft communication and tracking systems during rendezvous....

NASA Engineering & Safety Center (NESC) subject matter experts analyze records in various International Space Station and shuttle databases to identify recurring anomalies. The key problems these experts face in analyzing such database records are:

A new method for optimizing yaw attitude maneuvers on the International Space Station (ISS) was developed. Docking and undocking operations often require 180° yaw rotations, which are the most common large maneuvers on the ISS. When optimized, some large maneuvers,...

Modern spacecraft, aircraft, and surface vehicles support complex science missions in harsh environments. These spacecraft and vehicles provide diverse functionality that is deployed on increasingly complex and heterogeneous hardware and mechanical systems, with stringent...

The GOES-R Program has requirements to maintain knowledge of the GOES-R satellite onboard memory contents, including managing general satellite operations tables; processor memory dumps for memory verification; creating command loads, memory (table) loads, and command sequences to operate the satellite; verifying...

Amore efficient structural verification process for small satellites has been demonstrated. This new process eliminates the need for payload-specific coupled loads analysis (CLA) and simplifies structural testing while not increasing mission risk. The process...

This Android app provides a native interface to the Lunar Mapping and Modeling Portal’s (LMMP) lunar data archive and analysis tools. It complements the iOS app previously released, incorporating a very similar feature set. Both apps contain a subset of the functionality available in the desktop/Web version. Compared to the iOS...

Efficient support of planetary surface missions typically requires an orbiting asset that acts as a relay point to/from Earth. Orbital relay passes are normally 5 to 15 minutes in duration over any specific landed site. When multiple landed assets are co-located or near-located in the...