Semiconductors & ICs

A micro-electrofluidic-spray propulsion (MEP) system was built on a micro scale, in which arrays of hundreds of nano-thrusters are etched on silicon wafers like ICs, only a centimeter on a side. Many dozens of these thruster chips can be...

Wide-temperature and extreme-environment electronics are crucial to future missions. These missions will not have the weight and power budget for heavy harnesses and large, inefficient warm boxes. In addition, extreme-environment...

For certain semiconductors with important applications, the existing bulk crystal growth technique from the melt usually results in poor-quality multi-crystalline ingots that cause the typically low yield of the commercial growth process. The...

Current RHBD electronics are limited to speeds that approximate 250 MHz, regardless of the electronic process. The fact that determines the final speed is based on the nature of the current SEU (single-event upsets) radiation-tolerant latches, and the data flow between the latches through combinational...

Amethod was developed to model polymorphic heterogeneous multicore processors at a high level of abstraction, and formally verify them. The Bahurupi polymorphic heterogeneous multi-core architecture allows the combination of multiple simple processor cores — which...

The current flight software approach is monolithic in nature. Every module has tentacles that reach deep within dozens of other software modules. Because of these interdependencies between modules, functionality is difficult to extract and reuse for other missions.

The configuration of the reprogrammable field-programmable gate array (FPGA) currently on the market is very susceptible to single event upset when it operates in radiation environments. The current state-of-the-art approach is to refresh the configuration...

To enable NASA’s next-generation missions, there is a critical need for a reconfigurable field programmable gate array (FPGA) that can withstand the wide temperature ranges and radiation of the space environment while consuming minimal power without...

This innovation is a sub-nanosecond time-interval measurement that is compact and inexpensive, implemented in a field-programmable gate array (FPGA). Currently, high-speed count ers or semi-custom or custom ASICs (application specific integrated circuits) are used for time-interval...

Accurate assessment of circuits at cold temperatures is extremely difficult due to lack of models and tools that can simulate circuit behavior at cryogenic temperatures. A library of cryogenic temperature models was built, as well as a circuit simulator that can use those models and simulate...

Porous silicon nanowires are fabricated by two-step, metal-assisted electroless chemical etching of p-type or n-type silicon wafers. This method, in combination with nanolithography or nanopatterning, can be applied to fabricate porous silicon nanostructures of different...

Flexible circuits with superconducting wiring atop polyimide thin films are being studied to connect large numbers of wires between stages in cryogenic apparatus with low heat load. The feasibility of a full microstrip process, consisting of two layers of superconducting material...

Optical absorber coatings have been developed from carbon-based paints, metal blacks, or glassy carbon. However, such materials are not truly black and have poor absorption characteristics at longer wavelengths. The blackness of such coatings is...

Verilog-A based cryogenic bulk CMOS (complementary metal oxide semiconductor) compact models are built for state-of-the-art silicon CMOS processes. These models accurately predict device operation at cryogenic temperatures down to 4 K. The models are compatible...

A small-footprint, full surface-mount-component printed circuit board employs MOSFET (metal-oxide-semi-conductor field-effect transistor) power switches to switch high currents from any input power supply from 3 to 30 V.

Many distributed systems share common sensors and instruments along with a common power line supplying current to the system. A communication technique and circuit has been developed that allows for the simple inclusion of an instrument, sensor, or actuator node within any system containing a common power...

Multi-rate finite impulse response (MRFIR) filters are among the essential signal-processing components in space-borne instruments where finite impulse response filters are often used to minimize nonlinear group delay and finite-precision effects. Cascaded...

A small microprocessor, suitable for use in applications in which high reliability is required, was designed to be implemented in either an application-specific integrated circuit (ASIC) or a field-programmable gate array (FPGA). The design is based on commercial microprocessor architecture,...

A circuit topography is used to create usable, digital logic gates using N (negatively doped) channel junction field effect transistors (JFETs), load resistors, level shifting resistors, and supply rails whose values are based on the DC parametric...

A technique of monitoring digital closed-loop feedback systems has been conceived. The basic idea is to obtain information on the performances of closed-loop feedback circuits in such systems to aid in the determination of the functionality and integrity of the circuits and of performance margins.

A wireless avionics interface provides a mechanism for managing multiple broadcast transceivers. This interface isolates the control logic required to support multiple transceivers so that the flight application does not have to manage wireless transceivers. All of the logic...

A sequencer for a radar altimeter provides accurate attitude information for a reliable soft landing of the Mars Science Laboratory (MSL). This is a field-programmable-gate-array (FPGA)-only implementation. A table loaded externally into the FPGA controls timing, processing, and decision structures....