Manufacturing & Prototyping

A recent innovation has made manipulation of hazardous laboratory reagents in microgravity easier, thus enabling even more scientific research to be performed on the International Space Station (ISS). Prior to this innovation, moving fluids from container to container was performed only...

Additively manufactured 3D articles of certain high-temperature polymer composites such as ULTEM 1000 reinforced with chopped carbon fibers and printed by current state-of-the-art Fused Deposition Modeling (FDM) printers, suffer significantly...

A ceramic vacuum chuck is used to hold large detector arrays flat while being attached parallel to a rigid substrate. Once held in the vacuum chuck, the component is typically seized by epoxy against a rigid substrate. The problem that interferes with this operation happens when the epoxy...

There is great difficulty in implementing lateral gratings in GaSb-based lasers. Commercially, single-frequency GaSb lasers have been fabricated using metal gratings deposited laterally to the ridge-waveguide (RWG) stripe. The disadvantage of this is that the laser...

The objective of this work was to develop a thin film metal liftoff process that would allow one to accurately pattern two-micron-wide (or wider) features. The goal of this innovation was to pattern thin metal films on silicon substrates. The thin metal films can be deposited using physical vapor...

Conventional filament extrusion processes are unsuitable for recycling materials on the International Space Station due to requirements for continuous monitoring and tuning, as well as poor filament dimensional control. The Positrusion process recycles scrap or waste thermoplastics into filament for 3D...

Laser absorption spectroscopy has emerged as one of the most important applications for semiconductor quantum cascade (QC) lasers, particularly in the mid-infrared spectral regime where many gases of interest exhibit fundamental absorption features. Laser absorption...

The development of a conformal nanotube process is enabling for many applications in solar physics and space astrophysics (e.g., direct detection and imaging of exoplanets). Coronagraphs are key heliophysics instruments because they image coronal mass ejections (CMEs), which are the most energetic...

Ion optics, or grids, for ion thrusters or ion sources are traditionally made by subtractive manufacturing methods such as milling/drilling or chemically etching holes from thin sheets of bulk material. This innovation uses additive manufacturing (AM), or 3D printing, to build the grids from...

ISAAC (Instrument Shared Artifact for Computing) offers adaptability, computation power, I/O bandwidth, digital interface standards, and data processing capability in a single, common, low-mass/power, and small-form-factor platform with significantly reduced, nonrecurring cost and risk...

Optical component fabrication using metals or ceramic materials involves many grinding and/or machining and polishing steps to achieve the proper form to the tolerances of imaging or photonic focusing instruments. These instruments range from infrared sensors, through visible and...

This innovation is a concept for a novel thermal architecture that would enable a day-long surface mission on Venus. A Venus lander mission could last much longer than a few hours on the surface of the planet by absorbing heat from the Venus environment, and from the electronics within the lander,...

Ongoing work in the development and characterization of sensory materials requires the development of shape memory alloy (SMA) powder or particles. These are embedded in structural material so that the progression of localized damage that occurs during fatigue crack growth will...

PICA (phenolic impregnated carbon ablator) was developed for the forebody heat shield of the Stardust Return Capsule. Conventional thermal protection system (TPS) materials of the time (primarily carbon phenolics) had high densities and thermal conductivities, yielding a TPS mass fraction...

NASA has developed a class of low-density, flexible ablators that can be fabricated into heat shields capable of being packaged, stowed, and deployed in space. Several flexible versions have been developed by infiltrating a pyrolyzing silicone resin into flexible, low-density felts made of carbon, polymer, or ceramic...

A nanomaterial thin-film device provides a low-cost, facile fabrication pathway to commercialize the technology to the sustainable energy market. Metal oxide thin films have been fabricated to a photoelectrochemical cell by solar energy. The prototype device uses both low energy cost...

Copper replaced aluminum nearly two decades ago as interconnect material in integrated circuit manufacturing due to its better electrical conductivity. The size of the interconnect wire has been steadily decreasing as Moore’s law has been progressing through various feature size...

A novel, all-organic electroactive device system has been fabricated with a single-wall carbon nanotube (SWCNT) film used as an alternative electrode. This system was fabricated with LaRC-Electro Active Polymer (LaRC-EAP) active layer and the SWCNT films by...

NASA’s endeavor to further enable long-duration manned space exploration requires further closure of the oxygen loop of the life support system that is currently realized aboard the International Space Station. Currently, oxygen is recovered from crew-generated carbon dioxide via the use of a Sabatier...